Operation
Idle and sleep
On this page
Two different things save power. The CPU waits for an interrupt whenever the main loop has nothing to do; this is invisible to the network. In 802.11 power save, a station tells its access point that it sleeps and turns its receiver off between beacons.
CPU sleep
The main loop sleeps with the ARM966E-S’s wait for interrupt (mcr p15, 0, r0, c7, c0, 4). The core wakes when any source the interrupt controller lets through is pending, whether or not IRQ is masked in the CPSR, and also on the MAC’s FIQ line.
When
Each owner exposes an activity fingerprint: HIF ring cursors, RX FIFO offsets and the frame being decrypted, AES transfer states, host TX context states and MAC events serviced. A pass of the loop that changes none of them is idle.
Once passes have been idle for 5 ms, every idle pass ends with a sleep. The sleep’s programmed timeout is the time to the next timed work:
- the pipe watchdog, every 200 ms;
- beacon-loss detection;
- an ADDBA response, or a BlockAck an aggregate still waits for;
- the end of a scan dwell, or the next probe request;
- an access point’s next beacon;
- a power-save deadline: the end of a doze, a null frame to retry, or the idle time before dozing.
While any work is still in flight, such as frames queued for the MAC, a frame being decrypted or held for reordering, or output the host has not read, the timeout is capped at 1 ms instead: not every step of that work raises an interrupt or names a deadline. A scan step that tunes, settles or stops the radio keeps the loop awake.
How
With IRQ masked in the CPSR, the loop checks once more whether the IRQ handler has recorded a source. If not, it arms timer 1 with the timeout and waits for interrupt. Afterwards it stops timer 1, acknowledges IRQ 6 and unmasks IRQ. A source that becomes pending after the check still ends the wait, and the handler records it once IRQ is unmasked.
| Wake source | Seen as |
|---|---|
| Timer 1, the timeout | IRQ 6 |
| A host message or a finished transfer to the host | IRQ 13 |
| An AES transfer completing | IRQ 18 or 20 |
| A received frame, or any other MAC event | The FIQ line |
An associated, idle board wakes about 20 times a second, for beacons and the watchdog. The 5 ms linger keeps the loop awake between the frames of a flow: sleeping between them lost frames with one host driver.
Station power save
The host enables power save with SET_PM_REQ: mode 1 (legacy) or 0x81 (fast), with an idle time that defaults to 100 ms. The firmware records the mode, confirms the request and queues SET_PM_COMPLETE_IND; it does not wait for the access point. The indication reports 0x81 for either power-save mode, a legacy request included. Both modes then run as dynamic power save:
- Fall asleep. After the idle time without traffic, send the AP a null-data frame with the power-management bit set. A null frame that gets no ACK is sent again after 20 ms.
- Doze. While the AP considers the station asleep, nothing is in flight and no scan runs, turn the receiver off until 5 ms before a selected beacon: at most two beacon intervals ahead, never past a DTIM, and never past the beacon-loss deadline. Dozes shorter than 5 ms are skipped.
- Listen. Bring the receiver back for the beacon; this takes about 3.6 ms. If its TIM says the AP holds frames for the station, send a null frame with the power-management bit clear. After a DTIM beacon that announces group frames, stay on until the last of them, for at most 10 ms. After a missed beacon, stay on until the next one.
- Wake. The station’s own data frames carry the power-management bit clear and wake it as well.
Receiver off and on
| Step | Hardware |
|---|---|
| Off | Clear RxDma.CONTROL.ENABLE and wait for ACTIVE to clear; stop the PHY’s current operation; PlatformControl.POWER_CONTROL = 0x10 |
| On | Retune the operating channel through full RF initialization, and restore the joined state as at the end of a scan |